{{ui.blackBar}}
FREE SHIPPING*Orders of $200 or more qualify. Free shipping applies to most products. Front doors, interior jammed doors & custom orders have shipping costs which are calculated at checkout.

Top Mount Spoked Marksman Hanger Assembly Instructions

Top Mount Spoked Marksman Hanger Assembly Instructions & Video

PDF instructions for this Hardware set are also available.

Top Mount Spoked Marksman Hanger Recommended Tools

  • Level
  • Tape Measure
  • Pencil
  • Drill with 1/8”, and 1/4”, Drill Bits and Phillips Bit
  • Socket Wrench With 9/16"

Top Mount Spoked Marksman Hanger Parts

  • Hanger Assembly
  • Lag Screw
  • Fastener Screw
  • Phillips Screw
  • 1" Washer
  • Anti-jump Bracket
  • Adjustable Spacers
  • Door Guide
  • Hard Stop & Rubber Bumper
  • Track

Top Mount Spoked Marksman Hanger Assembly Instructions

NOTE: Doors using Floor Mount Door Guides will have a groove on the bottom. Ensure this groove is on the opposite end of the Door Hanger Installation.

door mount floor guide groove

Installation for square-edge doors

Place the hanger on the top surface of the door, 2” from the edge of the door side and flush with the door front. Ensure the front of the hanger and the front of the door are facing the same direction (Figure 1).

Top Mount Spoked Marksman hanger square install step 1

NOTE: If the door is 3 or more inches thick, mount the hanger in the center between the front and back of the door.

Using a pencil, mark the screw hole placement on the door top.

Repeat steps 1 and 2 for the opposite end of the door

Drill two pilot holes for each hanger using an 1/8”bit (Figure 2).

Top Mount Spoked Marksman hanger install step 2

Attach the hanger to the door using two fastener screws (provided). Repeat the process on the opposite end of the door (Figure 3).

Top Mount Spoked Marksman hanger install step 3

Installation for curve-edge doors

Place the hanger on the top surface of the door, 2-3/4” from the edge of the door side and flush with the door front. Ensure the front of the hanger and the front of the door are facing the same direction (Figure 1).

Top Mount Spoked Marksman hanger square install step 1

NOTE: If the door is 3 or more inches thick, mount the hanger in the center between the front and back of the door.

Using a pencil, mark the screw hole placement on the door top.

Repeat steps 1 and 2 for the opposite end of the door

Drill two pilot holes for each hanger using an 1/8”bit (Figure 2).

Top Mount Spoked Marksman hanger install step 2

Attach the hanger to the door using two fastener screws (provided). Repeat the process on the opposite end of the door (Figure 3).

Top Mount Spoked Marksman hanger install step 3First Things First

Check to see if the floor below the track area is level. If the floor rises more than 1/2” the door may rub or not slide open completely. If the floor is not level, measure from the highest point of the floor surface to the recommended track placement and adjust track placement accordingly.

Ensure the track will be installed onto wall studs. If wall studs are not lining up with the installation a header will be required to provide the necessary strength and stability for the track and door.

Step 1: To determine where the track should be installed, first measure the height of the door, then add 2-1/4” to the door height. 1/2” of this total will be for the clearance between the bottom edge of the door and the floor. 1-5/8” will be from the top edge of the door to the center of the track. (Figure 1).

Top Mount Spoked Marksman hanger install step 7

Step 2: Using a level and a pencil, make a line above the doorway the same length as the track.

Step 3: Hold the track up to where the pencil line is visible through the holes in the track (Figure 2).

Top Mount Spoked Marksman hanger install step 8

Suggestion: Use pieces of double stick tape on the back of the track to help hold the track in place while completing steps 2 and 3.

Step 4: Mark an intersecting line in the center of each track hole (Figure 2).

Step 5: Take the track down, remove double stick tape (if used) and set the track aside.

Step 6: Drill out the marked holes using a drill with a 1/4” drill bit (Figure 3).

Top Mount Spoked Marksman Hanger install step 9

Step 7: Attach one end of the track to the wall with one hard or soft stop, one lag screw, and one washer (provided) using a socket wrench with 9/16” socket (Figure 4). Do not tighten.

Top Mount Spoked Marksman Hanger install step 10

Step 8: Repeat step 7 for the other end of the track.

Step 9: Install remaining spacers with lag screws and washers (provided) using a 9/16” socket wrench (Figure 5). Tighten all lag screws.

Top Mount Spoked Marksman Hanger install step 11

Step 10: Stretch rubber bumper (provided) over hard stop. Repeat for the hard stop on the other end of the track (Figure 5A).

Step 11: Hang the door (Figure 6).

Top Mount Spoked Marksman Hanger install step 12

Door Guide Installation

Step 12: With the door in the closed position, ensure the door is hanging straight using a bubble level.

Step 13: Position the Door Guide part way into the groove in the bottom of the door (Figure 7).

Top Mount Spoked Marksman Hanger install step 13

Suggestion: Use double stick tape on the bottom of the door guide to hold the guide in place.

Step 14: Install the Door Guide using a 1” phillips screw (provided) and a drill with a phillips bit.

Step 15: Slide the door toward the open position until the other side of the Door Guide is exposed.

Step 16: Install the second 1” phillips screw (provided) using a drill with a phillips bit (Figure 8).

Top Mount Spoked Marksman Hanger install step 14

Anti-Jump Guide Installation For Square-Edge Doors

Step 17: Place the Anti-Jump bracket on the door side, moving the bracket up until it is between 1/8” and 1/16” from the bottom edge of the rail. Mark the placement with a pencil.

Suggestion: Use double stick tape on the back of the anti-jump bracket to hold it in place on the door.

Step 18: Install the bracket to the door edge with 2 phillips screws (provided) using a drill with a phillips bit (Figure 9).

Top Mount Spoked Marksman Hanger install step 15

Step 19: Repeat steps 17 and 18 for the opposite end of the door.

Anti-Jump Guide Installation For Curve-Edge Doors

Step 20: Place the Anti-Jump bracket on the door side, moving the bracket up until it is between 1/8” and 1/16” from the bottom edge of the rail. Mark the placement with a pencil.

Suggestion: Use double stick tape on the back of the anti-jump bracket to hold it in place on the door.

Step 21: Install the bracket to the door edge with 2 phillips screws (provided) using a drill with a phillips bit (Figure 9).

Top Mount Spoked Marksman Hanger install step 15

Step 22: Repeat steps 20 and 21 for the opposite end of the door.

Get News & Special Offers
You've already subscribed to our list!Sorry, looks like your address is incomplete.Get ready to be inspired!
Hi {{storage.distributor.name}} Discounts Applied · Logout
Hide
Wish List
My Wishlist