{{ui.blackBar}}
FREE SHIPPING*Orders of $200 or more qualify. Free shipping applies to most products. Front doors, interior jammed doors & custom orders have shipping costs which are calculated at checkout.

Rockwell-4-in-1 Door Installation Instructions

The Rockwell-4-in-1 Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials and hardware needed to assemble any of the four styles are included. PDF instructions for the Rockwell-4-in-1 Door are also available.

Rockwell-4-in-1 Door Instructions & Video

Rockwell-4-in-1 Door Recommended Tools
  • Ratchet with 7/16” deep socket or a standard 7/16” socket with extension
  • Drill with Phillips Bit
  • Rubber Mallet

Rockwell-4-in-1 Door Parts
  • Side Stile Left (1)
  • Side Stile Right (1)
  • Bottom Rail (1)
  • Middle Rail (1)
  • Top Rail (1)
  • Grabber Screws (36*)
  • Top End Slats (1 each)
  • Top Center Slats (6 each)
  • Bottom End Slats (1 each)
  • Bottom Center Slats (6 each)
  • 6" Lag Bolts (8*)
  • 12" Falcon Door Pull (1)

Rockwell-4-in-1 Door Assembly Instructions & Video

Note: Your door has a mortise (a 1/2” groove that runs along the bottom of your door) that will house the door guide. When assembling the door make sure that all pieces with a mortise (pieces A1 and A2) are oriented with the mortise facing down toward the bottom of the door (the side that will be closest to the floor when the door is hung).

Assembling your door - Two Panel Door

Step 1: Slide all B slats to the right into A1 R. Next, slide A2, Bottom Rail, up to A1 R and the B Slats. Tap slats gently into place with a rubber mallet.

Rockwell Two Panel Fig 1

Step 2: Slide Center Rail A3 down on top of the B Slats and into Side Stile A1 R. Gently tap with a rubber mallet.

Rockwell Two Panel Fig 2

Step 3: Slide all C Slats down and to the right into Center Rail A3 and Side Stile A1 R. Then slide top rail A4 down over the tops of the C Slats. Gently tap with a rubber mallet.

Rockwell Two Panel Fig 3

Step 4: Slide Side Stile A1 L over to cover the left edge of your Door. If necessary, have someone help you hold all slats and rails in place while you are positioning all parts. Lightly tap all into place with a rubber mallet.

Rockwell Two Panel Fig 4

Step 5: Attach Stile A1 L and A1 R to the door using the 6” Lag Bolts. Insert and tighten by hand, then use a ratchet to tighten all Lag Bolts.

Rockwell Two Panel Fig 5

Half X Door

Complete Steps 1-5 from Two Panel Door Section

Step 6: When the Door is assembled, place A5, A6 and A7 (Diagonal Rails) onto the door’s bottom panel so the predrilled holes are facing up and so they form an X that runs from corner to corner. Attach using the 3/4” Grabber Screws and a drill with a Phillips bit.

Attach the Door Pull and your Door is ready to hang.

Rockwell Half X Door Fig 1

Z Combination Door

Complete Steps 1-5 from Two Panel Door Section

Step 6: When the Door is assembled gently tap all parts into place with a rubber mallet. Place both A5 Diagonal Rails onto the door so the predrilled holes are facing up and so they run the same way, from corner to corner. Attach using the 3/4” Grabber Screws and a drill with a Phillips bit.

Rockwell Z Combination Door Fig 1

Step 7: Attach the Door Pull and your Door is ready to hang.

Rockwell Z Combination Door Fig 1

Double X Door

Complete Steps 1-5 from Two Panel Door Section

Step 6: When the Door is assembled, gently tapvall parts into place. Place A5, A6 and A7v(Top Diagonal Rails) onto the door so thevpredrilled holes are facing up and so theyvform an X that runs from corner to corner.vAttach using the 3/4” Grabber Screws andva drill with a Phillips bit.

Repeat for B5, B6, and B7 (Lower Diagonal Rails).

Attach the Door Pull and your Door is ready to hang.

Rockwell Double X Door Fig 1
Get News & Special Offers
You've already subscribed to our list!Sorry, looks like your address is incomplete.Get ready to be inspired!
Hi {{storage.distributor.name}} Discounts Applied · Logout
Hide
Wish List
My Wishlist