NOTE: Doors using Floor Mount Door Guides will have a groove on the bottom. Ensure this groove is on the opposite end of the Door Hanger Installation.
Lay the door with the front facing up on a flat, level surface.
Measure 3” from the edge of the door and draw a line parallel to the door edge about 7-1/2 inches in length (Figure 1).
Measure 3-5/8” from the top of the door. Using a pencil, mark the top hanger hole on the vertical line (Figure 1).
Measure 7-1/8” from the top of the door. Mark the bottom hanger hole on the vertical line (Figure 1).
Repeat steps 2-4 for the opposite end of the door. Set the hangers aside.
Drill two pilot holes all the way through the door for each hanger using a drill with an 1/8” drill bit (Figure 3).
Turn the door over. Using a 1-1/8” Forstner bit*, drill a 7/16” deep hole into each pilot hole (Figure 4). *A 1-1/8” Spade bit may be used in pace of a Forstner bit.
Turn the door over, returning it to the face-up position. Drill all the way through the pilot holes using a drill with a 1/2” drill bit (Figure 5).
Install the hangers to the front of the door using hex nuts and washers (provided) (figure 5-2).First Things First
Check to see if the floor below the track area is level. If the floor rises more than 1/2” the door may rub or not slide open completely. If the floor is not level, measure from the highest point of the floor surface to the recommended track placement and adjust track placement accordingly.
Ensure the track will be installed onto wall studs. If wall studs are not lining up with the installation a header will be required to provide the necessary strength and stability for the track and door.
Step 1: To determine where the track should be installed, first measure the height of the door, then add 2-3/4” to the door height. 1/2” will be for the clearance between the bottom edge of the door and the floor. 2-1/4” will be from the top edge of the door to the center of the track. (Figure 1).
Step 2: Using a level and a pencil, make a line above the doorway
Step 3: The interior angle of the bracket should be in line with the edge of the door. This is individual preference and will depend on how far beyond the doorway the door will overlap. Draw a vertical line where the door will hang in the closed position(Figure 2).
Step 4: Position an end bracket so the interior angle of the bracket is in line with the vertical line and the line above the door is centered in the top hole of the bracket (Figure 2). Using a pencil, mark the position of both top and bottom holes.
Step 5: Drill out the marked holes using a drill with a 1/4” drill bit (Figure 3).
Step 6: Attach the end bracket using two lag screws (provided) using a socket wrench with 9/16” socket (Figure 4).
Step 7: Measure and drill holes for center spacer brackets along the line drawn above the doorway (Figure 5).
Note: Ensure all spacer brackets are located on a wall stud. If studs don’t align with the installation, a header will be required.
Step 8: Install center spacer brackets using lag screws (provided) (Figure 6).
Step 9: Install the track at an angle, inserting the end of the track into the end bracket and laying the track in the groove of the center spacer brackets (Figure 7).
Note: Ensure the notched side of the track is facing up with the taller side facing out.
Step 10: Slide the remaining end bracket onto the end of the track. Mark the holes for the end bracket using a pencil (Figure 8). Set the bracket aside.
Step 11: Drill out the marked holes using a drill with a 1/4” drill bit (Figure 9).
Step 12: Install the end bracket using two lag screws (provided) (Figure 10).
Step 13: Install hole plugs over the end bracket screws (Figure 11).
Step 14: Install the soft stop (Figure 12).
Step 15: Hang the door (Figure 13).
Step 16: With the door in the closed position, ensure the door is hanging straight using a bubble level.
Step 17: Position the Door Guide part way into the groove in the bottom of the door (Figure 14).
Suggestion: Use double stick tape on the bottom of the door guide to hold the guide in place.
Step 18: Install the Door Guide using a 1” phillips screw (provided) and a drill with a phillips bit.
Step 19: Slide the door toward the open position until the other side of the Door Guide is exposed.
Step 20: Install the second 1” phillips screw (provided) using a drill with a phillips bit (Figure 15).
Step 21: Place the Anti-Jump bracket on the door side, moving the bracket up until it is between 1/8” and 1/16” from the bottom edge of the rail. Mark the placement with a pencil.
Suggestion: Use double stick tape on the back of the anti-jump bracket to hold it in place on the door.
Step 22: Install the bracket to the door edge with 2 phillips screws (provided) using a drill with a phillips bit (Figure 16).
Step 23: Repeat steps 21 and 22 for the opposite end of the door.