Be Patient. Order in process.
Please do not click back or reload the page. Call 1 (800) 891-8312 with any questions.
FREE SHIPPING*Most orders over $500 qualify. Free shipping applies to Barn Door Hardware, Barn Doors, and Pocket Doors over $500. Front doors, interior doors, shower doors, any oversized door (wider than 3ft and taller than 7ft) and any special order doors have shipping costs which are calculated at checkout. Some barn door hardware track lengths do not qualify for free shipping.
The world's most trusted source for designer doors & hardware

Legacy Low Clearance Assembly Instructions

Legacy Low Clearance Assembly Instructions & Video

Download Instructions PDF for this Hardware set are also available.

Legacy Low Clearance Recommended Tools

  • Drill with 1/8”, 1/4” and 3/8” Bits, and Phillips Bit
  • Socket Wrench with 9/16” Sockets
  • 7/32" Allen Wrench
  • Level
  • Tape Measure
  • Pencil

Legacy Low Clearance Parts

  • Hanger Assembly
  • Lag Screw
  • Button Head Bolt
  • Phillips Screw
  • 1" Washer
  • Anti-Jump Bracket
  • Anti-Jump Block (For use on bi-parting door systems)
  • Door Guide
  • Hex Nut
  • Round Adjustable Stop
  • Low Clearance Track

Legacy Low Clearance Assembly Instructions

NOTE: Doors using Floor Mount Door Guides will have a groove on the bottom. Ensure this groove is on the opposite end of the Door Hanger Installation.

door mount floor guide grooveHanger Installation

A: Lay the door face up on a smooth, level surface.

B: Place the hanger on the door

Legacy Low Clearance install Fig 1

C: Adjust the placement of the hanger for a 2-7/8” gap between the top of the door and the top hole in the hanger.

D: The side of the hanger should rest 2-3/4” from the edge of the door.

E: Mark the center of each installation hole with a pencil.

Legacy Low Clearance install Fig 2

Repeat steps C-E for the opposite end of the door. Set the hangers aside.

A: Drill two pilot holes all the way through the door for each hanger using a drill with an 1/8” drill bit.

Legacy Low Clearance install Fig 3

B: Turn the door over. Using a 1-1/8” Forstner bit*, drill a 7/16” deep hole into each pilot hole. *A 1-1/8” Spade bit may be used in pace of a Forstner bit.

Legacy Low Clearance assembly Fig 4

C: Turn the door over, returning it to the face-up position. Drill all the way through the pilot holes using a drill with a 3/8” drill bit.

Legacy Low Clearance assembly Fig 5

D: Install the hangers to the front of the door using button head bolts, washers, and hex nuts (provided), using a 7/32” Allen wrench and 9/16” socket.

Legacy Low Clearance assembly Fig 6First Things First

Check to see if the floor below the track area is level. If the floor rises more than 1/2” the door may rub or not slide open completely. If the floor is not level, measure from the highest point of the floor surface to the recommended track placement and adjust track placement accordingly.

Ensure the track will be installed onto wall studs. If wall studs are not lining up with the installation a header will be required to provide the necessary strength and stability for the track and door.

A: To determine where the track should be installed, first measure the height of the door, then add 2-7/8” to the door height.

B: 1/2” of this total will be for the clearance between the bottom edge of the door and the floor.

C: 2-3/8"” will be from the top edge of the door to the center of the hole.

Legacy Low Clearance install Fig 1

D: Using a level and a pencil, make a line above the doorway the same length as the track.

E: Hold the track up to where the pencil line is visible through the holes in the track.

Legacy Low Clearance install Fig 2

Suggestion: Use pieces of double stick tape on the back of the track to help hold the track in place while completing steps D and E.

F: Mark an intersecting line inside each slotted hole wherever they work best for your wall (i.e. stud locations).

Take the track down, remove double stick tape (if used) and set the track aside.

A: Drill out the marked holes using a drill with a 1/4” drill bit.

Legacy Low Clearance install Fig 3

B: Attach one end of the track to the wall with C: one lag screw, D: and one washer (provided) using a socket wrench with 9/16” socket. Do not tighten.

Legacy Low Clearance install Fig 4

E: Install remaining lag screws and washers (provided) using a 9/16” socket wrench. Tighten all lag screws.

Legacy Low Clearance install Fig 5

A: Hang the door

Legacy Low Clearance install Fig 6

Door Guide Installation

B: With the door in the closed position, ensure the door is hanging straight using a bubble level.

C: Position the Door Guide part way into the groove in the bottom of the door.

Legacy Low Clearance install Fig 8

Suggestion: Use double stick tape on the bottom of the door guide to hold the guide in place.

D: Install the Door Guide using a 1” phillips screw (provided) and a drill with a phillips bit.

E: Slide the door toward the open position until the other side of the Door Guide is exposed.

F: Install the second 1” phillips screw (provided) using a drill with a phillips bit.

Legacy Low Clearance install Fig 9

Adjustable Stop Installation

A: Place the adjustable stop on your track.

Top Mount Low Clearance Bypass Fig 7

B: Position along the length of your track to stop door at the desired location. Tighten bolt with a 9/16” wrench/socket.

Hi {{storage.distributor.name}} Discounts Applied · Logout
Hide
Wish List
My Wishlist
Hide
Sample Room
My Sample Room
BOM
{{part.name}}
TEST MODE
{{part.price | myCurrency}}
Remainder
{{part.quantity}}
{{attribute.name}}
{{attribute.value}}
ui.bom
ui.productOptions.assignments
ui.inputs