Your order is processing
Please do not press the back button or refresh the page.
FREE SHIPPING*Orders of $200 or more qualify. Free shipping applies to most products. Front doors, interior jammed doors & custom orders have shipping costs which are calculated at checkout.

Contour Hanger Assembly Instructions

Contour Hanger Assembly Instructions & Video

Download Instructions PDF for this Hardware set are also available.

Contour Hanger Recommended Tools
  • Drill with 1/8”, 1/4”, and 3/8” Drill Bits, 1-1/8” Forstner Bit or 1-1/8” Spade Bit, and Phillips Bit
  • 9/16” and 5/8” Combination Wrench
  • Socket Wrench With 9/16" and 5/8" Sockets
  • Level
  • Tape Measure
  • Pencil

Contour Hanger Parts
  • Hanger Assembly
  • Lag Screw
  • Lag Bolt
  • Phillips Head Screw
  • 1" Washer
  • Acorn Nut
  • Door Guide
  • Soft Stop
  • Spacer
  • Anti-jump Bracket
  • Track

Contour Hanger Assembly Instructions & Video

NOTE: Doors using Floor Mount Door Guides will have a groove on the bottom. Ensure this groove is on the opposite end of the Door Hanger Installation.

Hanger Installation

Lay the door with the front facing up on a flat, level surface. damage has occurred, call 800-891-8312 and Rustica Hardware will expedite a replacement.

Place the hanger on the door (Figure 1).

Adjust the placement of the hanger for a 2-3/8” gap between the top of the door and the bottom edge of the wheel. Ensure the base of the hanger resting on the door is 3-1/8” from the edge of the door (Figure 2).

Mark the center of each installation hole with a pencil. (Figure 2).

Repeat steps 2-4 for the opposite end of the door. Set the hangers aside.

Drill two pilot holes all the way through the door for each hanger using a drill with an 1/8” drill bit (Figure 3).

Turn the door over. Using a 1-1/8” Forstner bit*, drill a 7/16” deep hole into each pilot hole (Figure 4). *A 1-1/8” Spade bit may be used in pace of a Forstner bit.

Turn the door over, returning it to the face-up position. Drill all the way through the pilot holes using a drill with a 3/8” drill bit (Figure 5).

Install the hangers to the front of the door using lag bolts, washers, and acorn nuts (provided) (figure 6).

First Things First

Check to see if the floor below the track area is level. If the floor rises more than 1/2” the door may rub or not slide open completely. If the floor is not level, measure from the highest point of the floor surface to the recommended track placement and adjust track placement accordingly.

Ensure the track will be installed onto wall studs. If wall studs are not lining up with the installation a header will be required to provide the necessary strength and stability for the track and door.

Step 1: To determine where the track should be installed, first measure the height of the door, then add 2-1/4” to the door height. 1/2” of this total will be for the clearance between the bottom edge of the door and the floor. 1-5/8” will be from the top edge of the door to the center of the track. (Figure 1).

Contour Hanger install step 1

Step 2: Using a level and a pencil, make a line above the doorway the same length as the track.

Step 3: Hold the track up to where the pencil line is visible through the holes in the track (Figure 2).

Contour Hanger install step 3

Suggestion: Use pieces of double stick tape on the back of the track to help hold the track in place while completing steps 2 and 3.

Step 4: Mark an intersecting line in the center of each track hole (Figure 2).

Step 5: Take the track down, remove double stick tape (if used) and set the track aside.

Step 6: Drill out the marked holes using a drill with a 1/4” drill bit (Figure 3).

Contour Hanger install step 6

Step 7: Attach one end of the track to the wall with one soft stop, one lag screw, and one washer (provided) using a socket wrench with 9/16” socket (Figure 4). Do not tighten.

Contour Hanger install step 7

Step 8: Repeat step 7 for the other end of the track.

Step 9: Install remaining spacers with lag screws and washers (provided) using a 9/16” socket wrench (Figure 5). Tighten all lag screws.

Contour Hanger install step 9

Step 10: Hang the door (Figure 6).

Contour Hanger install step 11

Door Guide Installation

Step 11: With the door in the closed position, ensure the door is hanging straight using a bubble level.

Step 12: Position the Door Guide part way into the groove in the bottom of the door (Figure 7).

Contour Hanger install step 12

Suggestion: Use double stick tape on the bottom of the door guide to hold the guide in place.

Step 13: Install the Door Guide using a 1” phillips screw (provided) and a drill with a phillips bit.

Step 14: Slide the door toward the open position until the other side of the Door Guide is exposed.

Step 15: Install the second 1” phillips screw (provided) using a drill with a phillips bit (Figure 8).

Contour Hanger install step 15

Anti-Jump Guide Installation

Step 16: Place the Anti-Jump bracket on the door side, moving the bracket up until it is between 1/8” and 1/16” from the bottom edge of the rail. Mark the placement with a pencil.

Suggestion: Use double stick tape on the back of the anti-jump bracket to hold it in place on the door.

Step 17: Install the bracket to the door edge with 2 phillips screws (provided) using a drill with a phillips bit (Figure 9).

Contour Hanger install step 17

Step 18: Repeat steps 16 and 17 for the opposite end of the door.

Anti-Jump Installation for bi-parting doors

Get News & Special Offers
You've already subscribed to our list!Sorry, looks like your address is incomplete.Get ready to be inspired!
Hi {{}} Discounts Applied · Logout
Wish List
My Wishlist
Sample Room
My Sample Room
{{part.price | myCurrency}}